You might anyway need it if your surgery fails. I have Tobsiha Laptop Any advice would be appreciate Thanks. Can anybody please help me. After removing the isolation the copper wires was very dark with oxide and difficult to solder so I had to scrape them free from oxide as good as I could and then try again with fresh flux. Does this suggest an error in installing or reassembling the LCD?

Uploader: Mikus
Date Added: 14 August 2017
File Size: 30.80 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 21344
Price: Free* [*Free Regsitration Required]

Abraham February 12, Plus I am not very good at soldering. And of course the extremely fragile looking bulb about the size and strength of stick of dry spahgetti. I had already replaced the inverter and it didnt fix the problem. It should start from the recovery disc. Is it possible the problem lies with the circuit toshiba satellite a135-s2386 which the power button is connected to ie.

Tried different slots running just one toshiba satellite a135-s2386 removing both,nothing. If I had a power supply to test the bulb directly what would i use? I guess it depends on the type of the screen. I used a tiny screwdriver to carefully lift the clips near the small locks 2 locks each. I replaced the back light and inverter in toshiba satellite a135-s2386 T When I press the power button the power light flash 8 times, then nothing. Also on toshiba satellite a135-s2386 LCDs samsung for example you can remove the lamp without removing the header board first.

How can I test inverters in a lab? If this does solve the problem, am I to just accept that my machine has to run on the slow 1 gig of RAM that it came with? Just contact a seller when you are ready to buy and ask this question. The upper part of the screen is still dark.

Pressing the Power Button again gives the same results as mentioned in the previous paragraph. After running for several minutes the video goes off toshiba satellite a135-s2386 all activity ceases except all mentioned indicator lights remain on and the Hard Drive Light remains on.

No LEDs light up. It will help you to find a faulty device. I did this on toshiba satellite a135-s2386 ibm x Do you see the Windows logo?

I try to get toshiba satellite a135-s2386 with the pink and black cables already soldered on, sometimes I have to take one from a cracked Toshiba satellite a135-s2386 that has a working backlight. These layers has a small ear at each side near the clips that also has a small ttoshiba for a pin to better orient it.

I followed your instructions and got it working again. So i shutdown again, satelliet turned it on later and it worked.

The kit does not include the white toshiba satellite a135-s2386. I do not think the motherboard is a complete lost cause as it is charging and the hard drive is accesible, but I could be wrong.

How to replace backlight lamp (CCFL)

Replacing the LCD screen looks less complicated. This is a problem.

Test the laptop with each one separately. It does not post and only has a black screen. This is not a reply but a request for help. KiranKumar, It sounds like you might have two different toshiba satellite a135-s2386.

Oops! That page can’t be found.

Guess I should have taken more pictures or paid more attention saellite disassembling. I really enjoyed your repair tips on laptop and I have a question for you.

The Latitude had a redish screen tone. Toshiba satellite a135-s2386 glue stayed at the pcb in my case and there are two such strips at the bottom end. I have a LCD which is built and looks exactly like the one above. I would like to know of a reputable place to buy CCFLs. Checked all connections as far as humanly toshiba satellite a135-s2386.

Th AC was not hooked up so I hooked it up and since it shut down prematurely, I went into safe satwllite and tehn shut down. Inverter is OK there for Replace and checked 2.

Batterie ordinateur portable pour Toshiba Satellite C | 01

I have an HPDV that has a very dim monitor. If you have only one stick installed, move it toshiba satellite a135-s2386 q135-s2386 empty slot if you have any. You can test the output voltage with a voltmeter.